The Effect of Structural Defects on the Thermal Conductivity of ZnS, ZnSe, and CdTe Polycrystals

ZnS, ZnSe, and CdTe polycrystals are experimentally investigated. Mechanisms are treated which restrict the thermal conductivity in samples prepared by recrystallization pressing and by deposition from the vapor phase and subjected to additional strain. Anomalies are observed on the temperature dependences of the thermal resistance of investigated samples, which are due to the special features of their phonon spectra and to the variation of the contribution made by longitudinal and transverse phonon branches to the heat transfer in the Debye temperature region and higher.     

金属基复合材料的热残余应力力学模型研究进展

金属基复合材料在高温制备的冷却过程中或热处理过程中由于组分间热膨胀系数（CTEs）的差异会产生较大的热残余应力，热残余应力对复合材料的宏观性能有着重要的影响。本文综述了分析金属基复合材料热残余应力的有限元模型和解析模型等理论模型，并指出有待深入研究的问题。     

Geochemical characteristics of the Yufuin outflow plume, Beppu hydrothermal system, Japan

Thermal water at Yufuin (Kyushu Island, Japan) is tapped through about 820 shallow wells and used mainly for hot-spring bathing purposes. Chemical and isotopic data for fluids from wells and fumaroles in Yufuin and Beppu indicate that the thermal activity at Yufuin represents a dilute, westward-flowing hydrothermal outflow plume from the Beppu hydrothermal system. Two other (eastward-flowing) outflow plumes have long been recognized at Beppu, but the Yufuin outflow plume is first recognized here. The Yufuin outflow plume is apparently a mixture of two end-member fluids: (1) deep high-temperature (250–300°C) fluid from the Beppu system having high chloride concentration (1400–1600 mg/L) and a δ¹⁸O value near −6.0%, and (2) meteoric water having low chloride concentration (≤7 mg/L) and a δ¹⁸O value near −9.2%.A permeable conduit for the vertical and lateral transport of deep fluid from the Beppu system is provided by the Yufuin Fault zone, which extends westward from the southern flank of Mt. Tsurumi volcano to the town of Yufuin. Stable isotope ratios and chloride concentrations for shallow groundwaters near the eastern end of the fault, at an elevation near 700 m, are consistent with those required for the low-chloride meteoric end-member of the Yufuin thermal waters. Recharge of this meteoric water, as well as mixing with the Beppu deep fluid, may occur along the Yufuin Fault. Enthalpy-chloride relations indicate additional conductive heating of the Yufuin waters, in the amount of 350–500 kJ/kg beyond that which can be accounted for by mixing between Beppu deep fluid and meteoric water. This could be a result of conductive heating with convection to a depth of 1–2 km. Estimates of the magnitude of the heat source for the Beppu hydrothermal system should take into account the heat being discharged at Yufuin.     

[NZP]陶瓷零膨胀性能的设计

研究了「ＮＺＰ」材料的零膨胀性能，并尝试对零膨胀的「ＮＺＰ」陶瓷作了设计，从晶体结构、原子复合、各向异性、显微结构和复合材料等方面提出了设计思路。     

AHMED experiments on hygroscopic and inert aerosol behaviour in LWR containment conditions: experimental results

Hygroscopic NaOH, CsI, CsOH and inert Ag aerosol behaviour at different temperatures and relative humidities (RH) has been studied in a well instrumented and controlled vessel of 1.81 m³ total free volume. Homogeneous thermal-hydraulic conditions for aerosol measurement in the vessel were achieved. The aerosol number and mass concentration were measured continuously during the experiments using a Condensation Nucleus Counter and a Tapered Element Oscillating Microbalance. The particle size distribution and chemical composition in the test conditions were measured by Berner low pressure impactors. In the case of NaOH the half life of the aerosol mass concentration was more than four times longer at low RH (22%) as compared to high RH (96%). The half lives of the CsOH and CsI aerosols were only twice as long at low RH as compared to high RH. Thus at high RH (96–97%) the half lives of CsOH and CsI were twice as long as the half life for the NaOH aerosol. The faster decay of the NaOH aerosol is due to the smaller density decrease of NaOH during water condensation. CsOH particles grew rapidly to their equilibrium size at all humidities. The measured equilibrium size for CsOH aerosol agree well with the calculated particle size at different RHs. Experimental results were also compared with calculations obtained by severe accident computer codes. These calculated results will be presented in a later paper.     

蒸汽压法测定导热油热分解温度的研究

根据克拉贝龙—克劳修斯方程，建立了国内外文献未见报道的测定导热油热分解温度的试验装置和试验方法，测定了大量国内外导热油的热分解温度，数据表明该法具有准确、简单、实用、省时、省力等优点     

一种高温蓄冷介质蓄放冷特性的应用研究

采用实验的方法获得了氯酸锂共晶盐的蓄放冷特性的实用关系式。这种介质的融点为８℃，单位体积蓄冷量比冰大３０％，适于用作空调系统中的蓄冷材料。     

热分层流动计算中若干差分格式的比较

本文应用常规的守恒方程及湍流模型，对二维池内热分层流动建立了数学模型，并在Ｐａｔａｎｋａｒ的压力校正法基础上对该数学模型进行了数值计算，计算中的差分格式为乘方格式、一阶迎风、二阶迎风和ＱＵＩＣＫ。通过与实验的比较分析，建议计算应采用ＱＵＩＣＫ格式，并在进行风格独立性试验的基础上使用加密网络。     

Effects of Surface Morphology and Composition Modification on Spectral Emissivity and Thermal Diffusivity Profile at High Temperatures

A new all-spectroscopic method for depth-resolved thermal diffusivity measurement of metallic specimens has been demonstrated. The method entails measurement of the mass entrained into a laser-produced plasma (LPP) plume in such a manner that the plume is representative of the specimen in elemental composition. Both the abundance of matter and its elemental composition are measured by time-resolved spectroscopy for each LPP plume. In order to delineate the morphology versus composition basis of the depth dependence, a new study on a Nichrome ribbon specimen heated by ohmic heating in a vacuum is presented. A set of depth-resolved thermal diffusivity measurements is carried out, while noting the attendant changes in the spectral emissivity and elemental composition at succeeding ablation layers. Additional measurements are carried out after the specimen has been treated under varying heating conditions. Preferential diffusion of chromium at high temperatures has been found to contribute to the dynamics of surface thermophysical properties at high temperatures. Representative LPP ablation is well suited for removal of surface impurities prior to thermophysical property measurements by the pulse heating technique.